PRODUCT INSTRUCTIONS

SX4® 4 & 6 GOBO TRAY • DISC TRAY (Modes 6 - 9)

Four channel setting switches are on the control box.
The MODE switch to the far left.

Address then X10 and X100

It is powered by 24 volt DC and controlled by DMX512, either from most color scroller power supplies or a standalone power supply. Once powered, the unit will show a red power LED to indicate the power is on. The unit is also fitted with a green LED which indicates the status of operation.

After it is powered, the unit needs to initialize to find the home position of the gobos. This takes about 2 seconds during which time the green LED will flash. Once the home sensing is complete the flashing will stop. If the LED is not lit then DMX is not present. If the LED continues flashing, it means there has been a fault detecting the sensor and the unit operates but without correct index positioning.

Set X1 Dial - This number is for gobo selection. Each gobo is individually selected according to the following table:

Set DMX address on SX4® - This number is the desk
control (fader) channel. Gobo will change at the levels shown in the charts below. Moves at maximum speed and via the shortest route.

Set DMX address on SX4® - This number is the desk
control (fader) channel. Gobo will change at the levels shown in the charts below. Moves at maximum speed and via the shortest route.

Set DMX address on SX4® - This number is the desk
control (fader) channel

Channel 1: Gobo will change at the levels shown in the charts as per Mode 1

Channel 2: Sets speed and direction per chart below

• Use the X100 switch on the SX4® to set direction
  and speed per chart below.
  
  
• Use the X10, X1 switch on the SX4® to set the
  display time of each gobo. Setting these switches from 1 to 99 varies the time in 0.1 second steps from 0.1 to 9.9 seconds.

GAM Product #TS6120, #TS6140
Rosco Product #206 3650 00000, # 206 3640 00000

Click to view separate spec sheet or download PDF
	SX4 Six-Gobo Instructions

X1 switch on SX4® will set the display time each gobo from 1 to 10 seconds.

• Set on 0 for 1 second
  
• Set on 9 for 10 seconds

X100 switch on SX4® selects the first position used
on the turret wheel.
X10 switch on SX4® selects the last position used
on the turret wheel.

If you have three patterns, you put them in positions 1,2 and 3. Adjust the X100 switch to 1 and the X10 switch to 3 and the unit will auto select those three positions only

• If X100 = 1 and X10 = 3, the selection order is
  1,2,3,2,1, etc
  
  
• If X100 = 1 and X10 = 3, the selection order is
  1,2,3,2,1, etc
  
  
• If X100 = 5 and X10 = 2, the selection order is
  5,6,1,2,1,6,5,6,1,2, etc
  
  

• X100 sets the direction - Select 1 for counterclockwise
  rotation or 2 for clockwise rotation
  
  
• X10, X1 sets speed of rotation - 00 is the slowest
  and 63 is the fastest speed

• Applies to single pattern disc effects.
  
  
• Select DMX control channel on SX4® switches X100, X10 and X1
  
  
• Selected channel fader operates speed and
  direction of rotation as per chart below

• Applies to single pattern disc effects
  
  
• Select DMX control channel on SX4® switches X100, X10 and X1
  
  
• Control channel fader operates index/rotate
  functions as per chart below

• Applies to single pattern disc effects and gobos
  
  
• Select DMX control channel on SX4® switches X100, X10 and X1
  
  Control channel fader has two functions:
  
  
• Operates as an indexing fader from zero to 99%
  
  
• If set at 100%, then it holds the disc in continuous rotation mode